Претрага
73 items
-
Analysis of the exhaust emissions inventory from auxiliary mining machines
Stevan Đenadić, Aleksandar Mirković, Jovana Mitrović, Filip Miletić, Predrag Jovančić, Dragan Ignjatović (2023)Open-pit coal mines are equipped with a large number of mining machines and vehicles with diesel engines. Due to common daily operation of these machines and vehicles large amounts of exhaust gases which contain numerous pollutants are emitted into the atmosphere. The demand to reduce air pollution induced the activities in developed countries to map and calculate all gases emitted by industries to formulate and select adequate preventive activities. In collaboration with machine manufacturers, emission standards for off-road machines ...Stevan Đenadić, Aleksandar Mirković, Jovana Mitrović, Filip Miletić, Predrag Jovančić, Dragan Ignjatović. "Analysis of the exhaust emissions inventory from auxiliary mining machines" in 9th International Conference Mining and Environmental Protection, University of Belgrade, Faculty of Mining and Geology (2023)
-
The optimization of auxiliary machinery in open-cast lignite mines: a case study of bulldozers
One of the most important prerequisites for the successful operation of the open-cast lignite mine is to carry out all the auxiliary works timely with the necessary quality. The most important and most commonly used auxiliary machines are bulldozers. Engaging time of bulldozers use is in direct relation with the coefficients of the time and capacity utilization of the continuous system for the excavation of coal and tailings, which indicates their importance. More than 100 bulldozers have been hired ...... Therefore, benefits emerging from this attitude on auxiliary machines selection, including savings and improvements, can be achieved by these activities: In-time replacement of auxiliary machines and vehicles; Usage of proven and quality machines with implemented unification as much as possible; I ...
... cycle of that machihe. Keywords: Open-cast coal mine, auxiliary works, bulldozers, optimization, availabilifty. 1. INTRODUCTION Dozers are most common auxiliary machines at open-cast coal mines, both by type and the scope of tasks these machines can be used for. In the open-cast lignite mines of Electric ...
... that open-cast mines are having sufficient number auxiliary machines (namely dozers) should be included into determination of their life cycle. These machines will complete all planned tasks and create optimal conditions for operation of main mining machines (bucket wheel excavators, belt conveyors and stackers) ...Dragan Ignjatović, Predrag Jovančić, Stevan Đenadić, Ivan Janković, Ivica Ristović. "The optimization of auxiliary machinery in open-cast lignite mines: a case study of bulldozers" in 7th International Symposium Mining and Environmental Protection, University of Belgrade, Faculty of Mining and Geology, Belgrade, Serbia (2019)
-
Analiza primene višekriterijumskih metoda u optimizaciji izbora hidruličnih bagera na površinskim kopovima uglja
Hidraulični bageri primenjuju se u različitim oblastima privrede a najzastupljeniji su u građevinarstvu i rudarstvu. Na površinskim kopovima sa kontinualnim sistemima, klasifikuju kao pomoćna mehanizacija a na površinskim kopovima sa diskontinualnim sistemima, kao osnovna mehanizacija. Kako je u oba slučaja njihova primena neizostavna, važno je izvršiti adekvatnu analizu postojećih podataka, u cilju optimizacije izbora tipa hidrauličnog bagera u odnosu na uslove rada datog površinskog kopa. U radu su opisane različite višekriterijumske metode koje su korišćene za analizu hidrauličnih bagera. ...... information which can affect the future purchasing decisions of this machinery. Key words: multi-criteria methods, open-cast coal mine, auxiliary machines, hydraulic excavators. https://doi.org/10.1016/j.procs.2015.07.081 https://doi.org/10.1016/j.procs.2015.07.081 ...
... in different areas of industry, most often in construction and mining. On open-cast coal mines with continuous systems, they are classified as auxiliary machinery, while on open- cast coal mines with discontinuous systems they are basic machinery. As their application is necessary in both cases ...Stevan Đenadić, Predrag Jovančić, Dragan Ignjatović, Filip Miletić, Ivan Janković. "Analiza primene višekriterijumskih metoda u optimizaciji izbora hidruličnih bagera na površinskim kopovima uglja" in Tehnika, Centre for Evaluation in Education and Science (CEON/CEES) (2019). https://doi.org/10.5937/tehnika1903369D
-
Application of the Fuzzy theory in the evaluation of operating parameters of auxiliary mechanization on open-cast coal mine, case study: pipelayers
Achieved operating parameters are the main indicator of the work quality and selection of mining machines. The effectiveness of a coal mine is correlated with the availability of basic and auxiliary machines. The main task of auxiliary machines in lignite mines is to achieve optimal working conditions. From an economic point of view, auxiliary machines generate up to 20% of the lignite mines' total costs. These are the primary reasons for analyzing their current work and making decisions in ...Stevan Djenadić, Miloš Tanasijević, Filip Miletić, Predrag Jovančić. "Application of the Fuzzy theory in the evaluation of operating parameters of auxiliary mechanization on open-cast coal mine, case study: pipelayers" in 8th Balkan Mining Congress, Belgrade, September 28-30, Rudarski instutut (2022)
-
Application of the Fuzzy Model in the Evaluation and Selection of Hydraulic Excavators on Open-Pit Lignite Mine
Stevan Đenadić, Miloš Tanasijević, Vladimir Milisavljević, Dragan Ignjatović, Predrag Jovančić (2021)The production of lignite in large open-pit mines is mainly performed with continuously operating equipment, where bucket-wheel excavators, bucket-chain excavators, belt conveyors, and spreaders are the basic machines. Smaller machines, usually of discontinuous operating nature, are commonly categorized as auxiliary machines. This paper presents the research related to the analysis of auxiliary machine parameters with the case study for a hydraulic excavator. The purpose of the analysis was to develop a model of rating quality of service of the ...Stevan Đenadić, Miloš Tanasijević, Vladimir Milisavljević, Dragan Ignjatović, Predrag Jovančić. "Application of the Fuzzy Model in the Evaluation and Selection of Hydraulic Excavators on Open-Pit Lignite Mine" in SSRN Electronic Journal, Elsevier BV (2021). https://doi.org/10.2139/ssrn.3945617
-
Development of the Cost-Based Model for Monitoring the Lifetime of the Earth Moving Machines
This paper presents the model for the identification of reference points on the lifetime curve of engineering systems. This curve commonly represents the increase and decline of failure in relation to time. A direct correlation between failure rate and costs is assumed in this paper, therefore, statistical and empirical analysis of costs provided reference points. This approach is used for positioning stages of the engineering system’s lifetime with a minimal number of failures and costs, regardless of whether these ...Electrical and Electronic Engineering,Industrial and Manufacturing Engineering, Control and Optimization, Mechanical Engineering, Computer Science (miscellaneous), Control and Systems EngineeringUgljesa Bugarić, Milos Tanasijević, Stevan Djenadić, Dragan Ignjatović, Ivan Janković. "Development of the Cost-Based Model for Monitoring the Lifetime of the Earth Moving Machines" in Machines, MDPI AG (2022). https://doi.org/10.3390/machines10110995
-
Self-Engineering: Possibilities for Maintenance Operations in the Mining Machines Industry
Self-engineering is a relatively new branch of knowledge that aims to understand how systems could “autonomously” re-configure or repair themselves without the intervention of the operators. A direct field of application is within the maintenance spectrum. Having systems or machines capable of self-detecting or even self-repairing could represent a game-changer, in capital asset fields such as the mining industry in particular. This paper aims to investigate the possible benefits and challenges of self-engineering / self-maintenance concerning mining machines, specifically bucket-wheel ...self-engineering, self-maintenance, maintenance operations, mining industry, bucket-wheel excavator, gearbox revitalizationSteven Manders, Milorad Pantelić, Vladimir Milisavljević, Alberto Martinetti. "Self-Engineering: Possibilities for Maintenance Operations in the Mining Machines Industry" in SSRN Electronic Journal, Elsevier BV (2021). https://doi.org/10.2139/ssrn.3945979
-
Risk management of machines in open pit mines
Kirin Snežana, Pantelić Milorad, Miljanović Igor. "Risk management of machines in open pit mines" in The Scientific Journal of the Society for Structural Integrity and Life 13 no. 3, -:Društvo za integritet i vek konstrukcija, Beograd (2013): 197-202. https://doi.org/-
-
Analysis of noise sources in power transformers and rotating electrical machines
Snežana Aleksandrović, Aleksandar Cvjetić. "Analysis of noise sources in power transformers and rotating electrical machines" in 5th International Symposium Mining and Environmental Protection MEP 2015, Vrdnik, Serbia, 10-13 June 2015, Belgrade : Faculty of Mining and Geology (2015)
-
Development of the Availability Concept by Using Fuzzy Theory with AHP Correction, a Case Study: Bulldozers in the Open-Pit Lignite Mine
Stevan Đenadić, Dragan Ignjatović, Miloš Tanasijević, Uglješa Bugarić, Ivan Janković, Tomislav Šubaranović (2019)Availability is one of the most used terms in maintainability engineering. This concept is used to denote: The quality of service of an engineering system, i.e., machines, weak points’ analysis, asset management, as well as making decisions in the process of life cycle management. Availability is an overall indicator and contains partial indicators that are oriented towards reliability, maintenance, and logistical support. Availability presents a variable value and changes in time and space. Usually, availability is shown as the ...... same conditions. The machines that are analyzed operate as auxiliary mechanization in an open-pit mine in the Electric Power Industry of Serbia’s Kolubara Mining Basin. The analysis covered three machines of type B1, 15 machines of type B2 and 14 machines of type B3. Machines are up to seven years ...
... with continuous systems is to carry out all necessary auxiliary works on time (cleaning the strips in striping and disposing, moving the transporter, making roads, etc.) [29]. This, of course, implies that the open-pit mine has enough machines and that they are available for operation. The direct ...
... efficiency of the auxiliary machinery and the operation of the basic mechanization (bucket-wheel excavators, belt conveyors, and spreaders) has been demonstrated. In case of low availability, the open-pit mine must have a larger number of units or there will not be enough machines for operation. In ...Stevan Đenadić, Dragan Ignjatović, Miloš Tanasijević, Uglješa Bugarić, Ivan Janković, Tomislav Šubaranović. "Development of the Availability Concept by Using Fuzzy Theory with AHP Correction, a Case Study: Bulldozers in the Open-Pit Lignite Mine" in Energies, MDPI AG (2019). https://doi.org/10.3390/en12214044
-
A Fuzzy Expert Model for Availability Evaluation
Each technical system within itself carries the great potential danger of possible occurrence of failure and damages. Mining machines are characteristic by great investment values, costs of unplanned shutdowns, complex working conditions, and environment and workers hazards. Systematic monitoring of the mining machinery is of great importance for the management of the mining companies. Availability is the overall concept of quality of service. Includes information regard to operating state, an idle state, a standby state and shut down. The ...... AVAILABILITY OF BULLDOZERS Availability of bulldozers operating on surface lignite mines of Electric Power Industry of Serbia, which operate as auxiliary machines, is analyzed. Three different bulldozers (Liebherr - Lib, Dressta – Drs, Caterpillar - Cat), at three different surface mines (Drmno – D, Tamnava ...
... most common rate is “good” with a tendency towards ''average”. Figure 4.d shows that machines with the highest availability operate on the Field D, while the lowest availability is recorded for the machines on the Tamnava field. F. Verifications of results For bulldozers that operate at ...
... three different open pit mines in Serbia was evaluated using the proposed expert model. Machines were compared individually (selected machine at selected open pit mine), but also integral comparisons between machines and open pit mines were made. Obtain results should be used for the improvement of ...Dejan Ivezić, Miloš Tanasijević, Predrag Jovančić, Radiša Đurić. "A Fuzzy Expert Model for Availability Evaluation" in Proceedings of the 2019 20th International Carpathian Control Conference (ICCC), AGH University of Science and Technology, Kraków - Wieliczka, Poland (2019)
-
Multi-Criteria Approach for Selecting Optimal Dozer Type in Open-Cast Coal Mining
Ivan Janković, Stevan Đenadić , Dragan Ignjatović , Predrag Jovančić , Tomislav Šubaranović, Ivica Ristović (2019)... direct correlation with the work of the auxiliary (discontinuous) machinery, whose role is to accomplish all of the auxiliary workings on time. In effect, in the process of production in an open-cast coal mine, there must always be several different auxiliary machines available. The absence or insufficient ...
... direct correlation with the work of the auxiliary (discontinuous) machinery, whose role is to accomplish all of the auxiliary workings on time. In effect, in the process of production in an open-cast coal mine, there must always be several different auxiliary machines available. The absence or insufficient ...
... which consists of highly productive machines (bucket-wheel excavators, bucket-chain excavators, spreaders, conveyor-belt transporters, etc.) that provide an uninterrupted exploitation of mineral ores, the usage of auxiliary machinery is also necessary. The auxiliary machinery provides the possibility ...Ivan Janković, Stevan Đenadić , Dragan Ignjatović , Predrag Jovančić , Tomislav Šubaranović, Ivica Ristović . "Multi-Criteria Approach for Selecting Optimal Dozer Type in Open-Cast Coal Mining" in Energies, MDPI (2019). https://doi.org/https://doi.org/10.3390/en12122245
-
A fuzzy-based decision support model for effectiveness evaluation - a case study of examination of bulldozers
Effectiveness evaluation is one of the basic components of engineering asset management and maintenance engineering in general. Effectiveness is an overall concept representing a measurement of quality of service level for the analyzed engineering system. This concept contains a series of partial indicators relating to time in operation and time for maintenance activities, as well as functional properties of the system. This article describes the analysis and structuring of partial indicators, as well as the development of a model ...Miloš Tanasijević, Predrag Jovančić, Dejan Ivezić, Uglješa Bugarić, Radiša Đurić. "A fuzzy-based decision support model for effectiveness evaluation - a case study of examination of bulldozers" in International Journal of Industrial Engineering: Theory, Applications and Practice (2019)
-
Effectiveness Analysis of Different Bucket-wheel Excavators
Coal production in open-pit lignite mines in the Republic of Serbia is performed with continuous work systems. In addition to coal production, the same systems are used for the exploitation of large quantities of overburden. According to the reliability concept, continuous systems are in linear connection. If the failure occurs in one part of the system, that will produce a downtime of the entire system. The initial and most important factor of continuous systems is the bucket-wheel excavator. It ...Stevan Đenadić, Predrag Jovančić, Dragan Ignjatović, Miloš Tanasijević, Filip Miletić. "Effectiveness Analysis of Different Bucket-wheel Excavators" in 8th International Conference Mining and Environmental Protection, Sokobanja, 22-25 September 2021, University of Belgrade, Faculty of Mining and Geology, Belgrade, Serbia (2021)
-
Ostvarivanje dobiti pri uvođenju sistema agregatnih zamena na osnovnoj rudarskoj mehanizaciji površinskih kopova EPS
Jedan od osnovnih zadataka na površinskim kopovima uglja je ostvarivanje zadovoljavajućeg vremenskog i kapacitetnog iskorišćenja kontinualnih sistema. Da bi se to postiglo, neophodno je izvršiti izmene u postojećoj strategiji održavanja. Preduslov je uvođenje agregatne zamene vitalnih delova na rudarskim mašinama. Benefiti su višestruki. Očekivani rezultati ovakvog pristupa su: smanjenje zastoja i povećanje vremena rada; direktne materijalne uštede; bolja organizacija rada; racionalizaciju radioničkih i magacinskih kapaciteta; povećanje vrednosti mašina. Da bi se uvela agregatna zamena neophodne su investicije za nabavku ...Predrag Jovančić, Ignjatović Dragan, Đenadić Stevan. "Ostvarivanje dobiti pri uvođenju sistema agregatnih zamena na osnovnoj rudarskoj mehanizaciji površinskih kopova EPS" in X Međunarodna konferencija UGALJ, Zlatibor, Srbija, 13-16. Oktobar 2021., Jugoslovenski komitet za površinsku eksploataciju (2021)
-
Belt Weigher Accuracy Limiting Factors
Aleksandrović Snežana, Jović Mihajlo (2010)Aleksandrović Snežana, Jović Mihajlo. "Belt Weigher Accuracy Limiting Factors" in Proceedings of 16th International Conference “Production and Use of Steel Wire Ropes, Conveyers and Hoisting Machines” 10 no. 7, High Tatras, Podbanské, Slovakia:BERG Faculty TU Košice (2010): 347-350
-
Integrating landslide magnitude in the susceptibility assessment of the City of Doboj, using machine learning and heuristic approach
In this work, landslide assessment of the Doboj City area was modeled by combining machine learning and heuristic tools. The machine learning part was used to map the Morphometric factor. i.e. probability of landslides based on relation between the magnitude of events and morphometric parameters: elevation, distance to streams, slope, profile curvature, and aspect. The Random Forest and Support Vector Machines algorithms were implemented in the learning protocol, which included several strategies: balancing of the training/testing set size, algorithm ...Cvjetko Sandić, Miloš Marjanović, Biljana Abolmasov, Radislav Tošić. "Integrating landslide magnitude in the susceptibility assessment of the City of Doboj, using machine learning and heuristic approach" in Journal of Maps, Taylor&Francis (2023). https://doi.org/ 10.1080/17445647.2022.2163199
-
Underground loading-haulage equipment selection with application of topsis method with different weighting methods of criteria
The choice of adequate mining machines is one of the most complex problems in the underground exploitation of mineral raw materials. The weight of such a decision is reflected in the high prices of these machines and the occurrence of even greater costs during their use if their choice was wrongly conceived. There are numerous examples from practice in which such decisions were made solely on the basis of comparing the prices of machines, without considering any of the ...utovarno-transportna mehanizacija, izbor, TOPSIS, entropija, standardna devijacija, težina kriterijumaVladimir Krivošić, Luka Crnogorac, Rade Tokalić. "Underground loading-haulage equipment selection with application of topsis method with different weighting methods of criteria" in Underground mining engineering, University of Belgrade - Faculty of Mining and Geology (2024)
-
Automated blasthole drilling in surface mining
Milanka Negovanović, Lazar Kričak (2021)Све већи развој аутоматизације у рударској индустрији утицао је на увођење нових решења у области аутоматизације бушења минских бушотина на површинским коповима. Највећи светски произвођачи опреме за бушење развијају решења аутоматизације која омогућавају рударским компанијама да постигну најбоље резултате у погледу квалитета, продуктивности и оперативних трошкова. Решења из области аутоматизације бушења се крећу од операција даљинског управљања до потпуно аутоматизованог бушења, праћења података у реалном времену и разних специјализованих алата за управљање подацима који повећавају безбедност и продуктивност ...Аутоматизација, бушилица,тачност, бушење,рударство,систем даљинског управљања,безбедност, продуктивностMilanka Negovanović, Lazar Kričak . "Automated blasthole drilling in surface mining" in 8th International Conference Mining And Environmental Protection, Sokobanja, 22 – 25th September 2021 Serbia, University of Belgrade, Faculty of Mining and Geology, Belgrade, Serbia (2021)
-
Development of the hybrid MCDM model for evaluating and selecting bucket wheel excavators for the modernization process
This paper presents a methodology for evaluating and ranking different bucket wheel excavators (BWE) for determining which machine should enter in the process of revitalization and modernization. Various multicriteria methods are used. Combining them achieves the best effect when choosing BVE for the modernization process. AHP, TOPSIS, VIKOR, and PROMETHEE methods are used. The hybrid models are developed from the multi-criteria decision making (MCDM) methods and they are used to evaluate the basic indicators that characterize the operation of ...Snezana Savkovic, Predrag Jovancic, Stevan Djenadic, Milos Tanasijevic, Filip Miletic. "Development of the hybrid MCDM model for evaluating and selecting bucket wheel excavators for the modernization process" in Expert Systems with Applications, Elsevier BV (2022). https://doi.org/10.1016/j.eswa.2022.117199